Inflating tires on your own is a skill that must be learned when you own a Jeep Wrangler. This skill is essential when you get a flat tire, or your vehicle’s tire lacks air pressure. Fortunately, a Jeep Wrangler is equipped with a tire service kit that can be used to inflate Jeep tires.
So, how to inflate Jeep tires? You can quickly inflate Jeep tires using the tire service kit available inside your vehicle. This article will guide you through the step-by-step process of using the tire service inflating Jeep tires.
Table of Contents
Inflating Jeep Tires using the Tire Service Kit
If you get a flat tire, knowing how to use your tire service kit system will help you get back on the road quickly and safely. The tire service kit in your vehicle can be found under the load floor behind the rear seat.
If your service kit arises on the road, you need to pull over in a safe location and turn on the vehicle’s hazard lights. Then, you will need to position that tire that needs inflating so the valve stem will be located on the ground.
Doing this action will allow the tire service kit hoses to reach the valve stem with the tire service kit flat on the ground. Then, place the transmission in the park, turn off the ignition, and set the parking brake. After that, the tire service kit was positioned on the ground next to the flat tire to start the inflating process.
Step 1: Preparing the Tire Service Kit
In preparing the kit, push in and turn the mode select knob to the sealant mode position and uncoil the clear sealant hose. Then, remove the cap from the fitting at the end of the hose. Then, remove the valve stem cap and screw the sealant hose fitting onto the valve stem. After that, uncoil the power plug on the kit and connect it to the vehicle’s power outlet.
Step 2: Sealing the Tire
Push the power button on the tire service kit to let the sealant flow from the bottle through the hose and into the tire. You will need to run the pump until the sealant stops flowing into the flat tire. The pressure will read at 70 psi or 4.8 bar. However, it will quickly drop once the sealant bottle is empty.
Step 3: Inflating the Tire
The pump in the tire service kit will start to add air to the tire after the bottle is empty. You will need to continue to fill the tire with the correct pressure indicated on the tire placard. If the tire does not inflate to 26 psi or 1.8 bar within 15 minutes, the tire is probably damaged and will need to be replaced immediately.
Step 4: After Inflating the Jeep Tires
Once the tire reaches the correct pressure, turn the pump off. Then, you must remove the speed limit sticker reminder found at the top of the sealant bottle and place the sticker on the instrument panel.
You must disconnect the sealant hose from the valve stem and install the valve stem cap. Then, unplug the kit from the power outlet and place the kit in its sproper storage location.
Step 5: Testing the Jeep’s Tire
To test your tires, you must drive the vehicle for 5 miles or 8 kilometers, or 10 minutes to ensure the sealant is distributed within the tire. As the sticker says, do not drive the vehicle faster than 50 mph or 80 km/h.
Once you finish driving the distance, pull over your vehicle to a safe place to check the tire pressure using the tire service kit. Push in and turn the mode select knob on the kit to the air mode position.
Plug the tire service kit into the empower outlet and connect the black air hose to the valve stem. Check the tire pressure on the gauge. If the pressure is less than 19 psi or 1.3 bar, wait to drive the vehicle until you have replaced the tire. If it has more than 19 psi or 1.3 bar, add the air necessary to return the correct pressure indicated on the tire placard.
If the tire becomes overinflated, you need to push the deflation button to reduce the tire pressure to the recommended level. Disconnect the tire service kit from the valve stem and install the valve stem cap. Unplug the kit from the power outlet and place the kit in its proper storage location.
Inflating Jeep Tires at a Local Gas Station
To inflate your Jeep tires using the air dispenser at a nearby gas station, pull up to the dispenser and ensure you can reach all four tires with the air hose. Start with the first tire by removing its valve cap. Then, use a tire gauge to check the current air pressure in that tire.
Once you have the reading, proceed to repeat this process for the remaining three tires, checking and adjusting the air pressure as necessary. Regularly maintaining the proper tire pressure will enhance your Jeep’s performance, fuel efficiency, and overall safety on the road.
Conclusion
Learning how to inflate Jeep tires is essential for your safety, tire longevity, and fuel efficiency. Maintaining the correct tire pressure will help in taking care of your vehicle. Knowing how to inflate the tire independently will provide peace of mind during emergencies like flat tires.